1-channel Green Light Switching Expansion Module with DALI Communication
Model: GL-EXP-SW-DALI
Part #: 6507041
- Single-channel lighting switch
- DALI® system interface
- Supports on/off switching of LED, incandescent, fluorescent, magnetic low-voltage, electronic low-voltage, neon/cold cathode, and high-intensity discharge lighting loads
- Also supports on/off switching of motor loads
- Built-in air gap relay
The Crestron Green Light® GL-EXP Series delivers a family of professional lighting control modules for Cresnet® or DALI® based lighting systems. Designed for easy installation on a wall or above a suspended ceiling, these modules offer a perfect solution for adding extra lighting zones to any system without requiring an additional lighting cabinet.
The GL-EXP-SW-DALI is a single-channel switch expansion module designed to control a wide range of non-dimmable lighting loads including LED, incandescent, fluorescent, magnetic low-voltage, electronic low-voltage, neon/cold cathode, and high-intensity discharge. It can also be used to switch motor loads.
DALI® Communications
The GL-EXP-SW-DALI communicates using the DALI (Digital Addressable Lighting Interface) standard, which enables interoperability with other DALI compliant lighting control products from Crestron and other manufacturers. Interfacing a network of DALI switches and other devices with a Crestron lighting control system is facilitated using the DIN-DALI-2.
Emergency Lighting Control
The GL-EXP-SW-DALI is UL® 924 listed for use in controlling an emergency lighting load. In the event of a power failure indicated by a loss of DALI network communication (system failure), the GL-EXP-SW-DALI turns on the lighting load if it is off (assuming line power is supplied by a backup power source).
Plenum Rated NEMA Enclosure
The GL-EXP-SW-DALI is designed to be mounted to a vertical surface and is UL 2043 compliant to allow for installation in an environmental air-handling space above a suspended ceiling. Conduit knockouts are provided on the bottom and lower sides of the unit. All connections are made via screw terminals behind the front cover.
- Single-channel lighting switch
- DALI® system interface
- Supports on/off switching of LED, incandescent, fluorescent, magnetic low-voltage, electronic low-voltage, neon/cold cathode, and high-intensity discharge lighting loads
- Also supports on/off switching of motor loads
- Built-in air gap relay
- UL® 924 listed for emergency lighting control
- Surface mountable NEMA Type 1 enclosure
- Mounts on a wall panel or above a suspended ceiling
- UL 2043 listed for installation in an environmental air handling space
- Spec Sheet available - Yes
- Operating Temperature (Maximum): 104 F
- Operating Temperature (Minimum): 32 F
- Certifications: UL, FCC
- AC Voltage (Maximum): 277 Volts
- AC Voltage (Minimum): 100 Volts
- Depth: 3.16 in
- Height: 8.78 in
- Width: 6.39 in
- Product Weight: 3.43 lbs
- Current Draw: 16 Amps
- Load Control:
•Switch Channels: 1
•Switched Load Types: LED, incandescent, fluorescent, magnetic low-voltage, electronic low-voltage, neon/cold cathode, high-intensity discharge (HID), motor - COMMUNICATIONS:
•DALI: DALI control gear, IEC 62386 compliant - Connections:
•NEUT: (3) Captive screw terminals
•Neutral connections for feed and load
•24 to 10AWG (0.25 to 4mm2) wire size
•LINE: (2) Captive screw terminals
•Line power feed input and pass-through
•24 to 10AWG (0.25 to 4mm2) wire size
•SW: (1) Captive screw terminal
•Switched load output
•24 to 10AWG (0.25 to 4mm2) wire size
•DALI: (2) Sets of (2) captive screw terminals
•DALI control gear interface ports
•26 to 14AWG (0.14 to 1.5mm2) wire size
•For use with Class 2 wiring only
•Ground: (1) 3-terminal grounding block - Controls and Indicators:
•PWR: (1) Green LED, indicates line power is applied to either LINE terminal
•NET: (1) Yellow LED, indicates DALI network communication
•ERR: (1) Red LED, indicates a variety of error conditions via blinking patterns (refer to the installation guide)
•ON/OFF: (1) Pushbutton and (1) red LED, pushbutton toggles the load output on and off, LED indicates the load output is energized
•RESET: (1) Pushbutton, initiates hardware reset - Construction:
•Enclosure: NEMA Type 1, galvanized steel with gray matte powder coated removable front cover panel, extruded aluminum heat sink on rear, (2) integral mounting flanges, (4) 1/2 or 3/4" conduit knockouts on bottom and lower left and right sides
•Mounting: Surface mount, must be oriented upright and mounted to a vertical surface with 6 inches (153mm) minimum spacing above and below for proper ventilation and heat dissipation
Inland AV
422 Lucas Ave
CenterPort, MB R4B 0A7
Canada
(204) 786-6521
https://inlandav.ca/